Click OK.Īfter the above configuration, you can now launch a third-party WOL software on PC B and send a Magic Packet to boot up PC A. Specify the internal server IP as 192.168.0.100, which is the IP address of PC A. Specify the external port and internal port as 7, which is used to receive Magic Packets. Specify the WAN port according to the network environment. Click OK.Ĭhoose the menu Transmission > NAT > Virtual Servers and click to load the following page. Enter the IP address and MAC address of PC A. If there is not a desired entry, click to load the following page. Check if the desired IP address is reserved for PC A. Click OK.Ĭhoose the menu Network > LAN > Address Reservation to load the following page. Enable Export to DHCP Address Reservation. In the IP-MAC Binding List section, click to load the following page. In the Scanning Result section, click the corresponding to bind MAC and IP address of PC A.Ĭhoose the menu Firewall > Anti ARP Spoofing > IP-MAC Binding to load the following page. Wait a minute until the scanning is completed. In the general section, specify the scanning IP range according to the DHCP address pool. If the desired entry is in the list, click the corresponding to bind MAC and IP address of PC A.Ĭhoose the menu Firewall > Anti ARP Spoofing > ARP Scanning to load the following page. There are three methods to do IP-MAC binding: bind in the ARP list, bind in ARP scanning result, or add IP-MAC Binding list entry manually.Ĭhoose the menu Firewall > Anti ARP Spoofing > ARP List to load the following page. To achieve this requirement, you can configure the router as follows:Īfter you complete the configuration, you can use a WOL software to wake up PC A on PC B.įollow the steps below to configure the router. Make sure the WAN port of the router is routable from PC B.PC A should be powered off normally and the power supply is normal.In network card properties configuration of PC A, allow the network card to wake up the PC, forbid the PC to turn off the network card to save power, and enable Wake on Magic Packet. Make sure that the network card of PC A supports WOL.In BIOS setup of PC A, enable Power On By PCIE or Wake Up On LAN. Make sure that the motherboard of PC A supports WOL.It is required that PC B can wake up PC A by sending a Magic Packet via the internet.īefore configuring WOL, you should do the following preparation: In the diagram below, PC A is connected to the internet via the router. That's all it takes to forward your ports for Wake on LAN.You can use WOL (Wake on LAN) to boot up your PC from a remote place by sending a Magic Packet via the internet. List of Routers - Customized for Wake on LAN You can choose your router from our list to see exactly how to forward ports for Wake on LAN: Some routers need to be rebooted in order for the changes to be saved. Enter the TCP and UDP ports that you need to forward for Wake on LAN in the corresponding boxes in your router.It’s also possible to do via your tablet or smartphone. then configure the router for port forwarding and configure TeamViewer in order to use Wake-on-LAN. Put your computer's IP address in the proper box in your router. Find out more about TeamViewers Wake-on-LAN tool and how you can turn on (and off again) a PC remotely, quickly and easily from your client console.Locate the section in your router that deals with port forwarding.You can start by logging in to your router.The step-by-step process for forwarding a port is: Network Utilities lets you manage port forwards by putting them in when you need them and also removing the ones that you no longer need which maximized network security.Īlternatively you can do it by hand. The easiest way to forward your ports is to use our Network Utilities software. You can also follow our Find Your Router IP Address article. Our Router Detector tool is free to use and is part of our Network Utilities software. You can run our free Router Detector software to locate your router's IP address.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |